Search results

I'm Confused. On a Head Gasket, where the Copper or Steel wraps around (rolled edge) about 1/16 of an inch, and crimped. Which way does it go on Engine, Up towards the Head, or Down towards the Block??? I was always told, the stamped Manufactures Name goes up, against the Head, if it doesn't...

I acquired a Exhaust Manifold without any Pits on it, best I have ever found, the Intake had a carb mounting ear broken off, so I'm using another Intake. While I have them split, I sandblasted them, the Exhaust I sprayed with Eastwood Stainless Exhaust Coating and Ford Model A Green for the...

Wanted a Drivers Side Door for a 1930-31 Pick-up or AA Truck. I believe that Tudor Sedan uses the Same Door, maybe Coupe?? Size is 29 Inches Wide, 41 1/2 tall, 42 with top trim. I will Pay Shipping, Fed-ex is my Preferred Shipper. Need all Hinges also, but not Necessary, if you only have Door...

I just purchased a Model AA 157" Wheel Base Truck. The Numbers have been Ground Off the engine boss on the left side where they would Normally be. On the Rear of the Block, (1st time I have seen this on a Engine) It has Cast Letter of H then below it 14 or [4 as shown in the Photos below...

See post #12 for info of this years show, Sat Feb. 1st 2014 Anybody down here in South West Florida, Fort Myers area, going to the Show Tomorrow? http://www.edisonfordwinterestates.org/events/annual-events/antique-car-show/ I was seen Driving around the Streets of Punta Gorda since middle...

As a joke, my brother used to hang a pair of pantyhose over his fireplace before Christmas. He said all he wanted was for Santa to fill them. What they say about Santa checking the list twice must be true because every Christmas morning, although Jay's kids' stockings were overflowed, his poor...

I don't need a Radiator, I was just rummaging around on E-bay and found this. http://www.ebay.com/itm/HIGH-PERFORMANCE-aluminum-alloy-custom-radiator-Ford-model-1928-1931-/110966398669?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item19d61cdecd I looked up the Duty from China, this is...

I removed this Starter from a Model A Doodlebug I bought years ago. It has a Model A Car Engine, 1929 by the Block Number, and a AA Truck Bell Housing with a 4 speed Transmission. International Dump Truck Rear End. I took out the Starter Today to change the Starter Switch. This is what I found...

Well another Model A is saved, even if it wears different apparel. After 4 Summers of part time work on the A, it is Finally 95% Finished. I am Happy with the Way it turned out. It Runs and drives great. I have had every Part of it apart, cleaned, replaced, or rebuilt. Including Engine, Drive...

I installed my Head Light Bar on my Fenders today, 1930. Is it possible that I have it installed Wrong? Backwards! The cups are really pointing down, at i would say 30 Degree angle. When I went to Stowe I looked at 30s and 31s and thought they were pointed Forward. I have done a search, and come...

As a joke, my brother used to hang a pair of pantyhose over his fireplace before Christmas. He said all he wanted was for Santa to fill them. What they say about Santa checking the list twice must be true because every Christmas morning, although Jay's kids' stockings were overflowed, his poor...

I am Looking to purchase a Set, Right and Left. Wide Bed, Pick-up Fenders. Any one know of a Supplier who sells Metal Repos?? I can find Fiberglass ones, and Narrow Bed or Coupe Fenders in Metal, but they will not work with the Wide Radius 2-2 1/2 inch, where they meet the Splash Shields. I...

Looking to purchase a Set, Right and Left. Wide Bed, Pick-up Fenders. They don't have to be Mint, as will be used on a Driver, but not junk or complete Rust Buckets. Needing some Repair is OK. Usually found on a 1931 Box Narrow Bed or Coupe Fenders will not work with the Wide Radius 2-2 1/2...

As a joke, my brother used to hang a pair of pantyhose over his fireplace before Christmas. He said all he wanted was for Santa to fill them. What they say about Santa checking the list twice must be true because every Christmas morning, although Jay's kids' stockings were overflowed, his poor...

I need a Heater Cover for My Waffle Type Exhaust Manifold, the one with the 2 bolt holes in the top. Its just a daily driver.

#1- Today I installed the Steering Box and Column, in my near compleated Huckster Van. The steering Box hits the Bolt on the Starter Band, no space between at all. #2- Tried to install the Accelerator Linkage, like Les Andrews book says, Form the Inside then up, between Cowl Firewall and...

I have been looking for My registration for a 1930 Model A Pick-up for 28 Years. :) Finaly I found It, but I don't have the Truck!! :(:( Last time I registered it was 1981. I was going threw a D, and My son was 11 at the time. Of course his Mother agreed to Keep it in the Barn for Him and...