Search results

Gas cap and gasket $25.00 plus shipping. I only accept money orders.

Repro emblem (bought around 2010) $25.00 Plus, Shipping. I only accept Money Orders.

Hi all I just logged in today and noticed that a bunch of you sent me a private message. If you remember what you wanted, and still need them, please contact me again. Fan belt number 42-6324. Generator band 7J, Starter Band K-12 with some damage, Starter band L-3 pits where the number is, hard...

Hi Guys, I have 4 starter bands, Sandblasted and spray caned primed. The dates are, K-9, L-3, 3-K, K-12. I also have 1 generator band 7-J, sandblasted and painted with a spray can. Ask questions and I can send pictures to your email. I don't know how to post pictures on this site. $15.00 each or...

1930 Tudor, black with yellow wheels, rebuilt engine, less then 700 miles, ( matching VIN number to title ) rebuilt trans, starter, dist, water pump, carb, generator, steering box, front end including steering arms, radiator, wiring harness. What needs to be looked at are the rear brakes and...

:) 5 - 19" tires only, not road worthy, good for rolling around the shop. Will ship, you pay the shipping or pick up in CT. 203-464-4398 Dennis

Some good some bad, starters and gen cores, flywheels, clutch housings, bell housings, brake drum, backing plates, intake and exhaust, axle tubes, nuts and bolts, small parts, misc and blah blah blah. PICK UP ONLY. First call first served. 203-464-4398 Dennis. The small print---you must take it...

I have some useable parts and some not useable. Flywheels, axle tubes, starter and gen cores, misc nuts and bolts, backing plates, drums, bell housings, intakes, exhaust, clutch housings---blah blah blah. You must take the good and the bad no picking. Cleaning out garage to make room for another...

Hi all, I have a 1928 engine and it has an initials RC before the numbers. Does anyone know what the RC stands for? Thanks to all that reply> Dennis

1928 Model A engine. What can I say, It does everything it's suppose to do, it runs, it leaks oil, not water and it knocks.:rolleyes: No shipping, pick up only. I can meet you up to 30 miles from West Haven, CT. Best to call me at 203-464-4398. Dennis I have other parts, starter and...

I have a rebuilt motor with less than 500 miles and the exhaust gasket let go around 350 miles and now again around 500 miles. The exhaust manifold ( heater type ) was machined. I used the copper type gaskets the second time and it still blew out. Engine runs fine with no problems. Is there a...

Hi Ford Barn members. Here is my update, did not remove the trans, made adjustment through inspection hole. You can see where the lock nuts turned on the adjusting stud. The factory peened the nut into the stud groove but it still came loose. The fingers were about 1-1/8 inch away. Now, how and...

A little history on this problem. I had my engine rebuilt, found real good clutch and brake pedals that were not worn, rebuilt the trans and trans bell housing with new shafts and other hardware, installed a new ( maybe rebuilt ) pressure plate and disc and throw out bearing. 350 miles on all...

Starter for sale not tested $15.00 or trade, plus shipping.

Hi guys, I will be installing my intake and exhaust manifolds soon. Machine work is done. The question is, do you bolt together the intake and exhaust manifold then install it on the engine then torque the unit to the engine, or, do you loosely tighten the intake and exhaust together then torque...

Need one generator band, date doesn't matter, minor pitting OK. FOUND ONE AT A LOCAL SWAP MEET

Thanks for the info. from everyone.:cool: I did lube the oil holes in the linkage shaft that bolts to the engine with oil from my squirt can. Yesterday I used WD-40 and also found that the rubber grommet around the accelerator rod was rubbing against the rod. When driving the car and she warms...

When I drive my car for the first 10-15 mins, the idle is perfect, after about 30 mins. of driving the idle goes higher and I have to pick up the accelerator with my foot to lower the idle so I can shift gears. I have a new spring on the linkage and I lubed it with oil. Thanks to all that help...

I see pliers with the Ford script in different places :eek: on the handles. Is there a correct placement :) for the Ford script for Model A's ? :cool:

On the # 2,3,4 exhaust ports my black painted manifold turned white. The #1 port is black. This could be from running lean because I drive with GAV closed ? What else can you think of ? By the way this is a rebuilt engine with less then 300 miles. Carb,dist,gen,starter and water pump are all...