Search results

I installed a signal stat 900 in my ccpu. Have all the wires wired as in the diagram. Before I installed the lights, I tested the circuit. 6 volts were going to all wires when signals engaged. I installed the lights and the volts dropped to 3.44. I unhook the light and the wires go to 6 volts...

I am hooking up signal lights to my 29 ccpu. I have the front wired. I have 6 volts going to the lights when the signal switch is deactivated. When i activate the signal switch the volts drop to 3.66. Same way on the rear. Do I have a bad flasher or signal switch. I ran a direct ground from the...

Is there a sealant that holds the glass to the rubber and the glass channel When we install the rubber on the glass and put it in the glass channel it appears tight, but when we roll down the window the glass comes out of the channel. The glass appears to be sguare and moves up and down easily.

The 1929 model a closed cab pickup I have came without a top. I am now ready to start the the installation of the top wood. Are there any good instructional videos or cd's on this subject that I might find?

I have a 1929 model a pickup. The rear spring has a bolt with a round carriage type head on it. i would like to replace this bolt with a square head bolt. I already have the rear end pulled and lying on the garage floor with the rear spring intact. Is there a way to remove the center bolt and...

Stupid me, does the ridge on the bearing face the pressure plate or the ******? I can't remember, should have taken a photo be fore disasembly.:(

Has anyone removed a pickup bed from a 1929 closed cab pickup? Advice or tips will be appreciated.

Ok this is what is happening. Push in clutch pedal and the engine runs fine. Let out the pedal and the engine seems to be under a load and will stall if the clutch comes out this happens in any gear. This is even with the ****** in nuetral. I have a 1929 closed cab pickup with a 1930 4 banger...

Ok this is what is happening. Push in clutch pedal and the engine runs fine. Let out the pedal and the engine seems to be under a load and will stall if the clutch comes out this happens in any gear. This is even with the ****** in nuetral. I have a 1929 closed cab pickup with a 1930 4 banger...

Wiring up rust bucket to sealed beam head lights. My problem is that i have three wires coming into the bucket. I have found the parking light wire, but after grounding the light, there is no where to hook it. The light has three terminals 1 for the ground wire, 1 for the high beam and 1 for...

With the key on how many volts should go to the distrubuter. I have about 6 volts is this correct? I cant seem to get a spark to the plugs. Rotor is set at .025.:(

Everyone keeps saying the bevel goes to the rear of the car. My new ring gear has a bevel on the inside of the gear and the teeth are beveled. I think I go with the bevel on the teeth, but want to make sure

I am looking for a set of rear fenders for a 1929 closed cab pickup:(

I took everyone's advice. Put the flywheel on a sturdy surface and heated it with my propane torch. (The gear not the flywheel) A few good whacks with the chisel and off it came. I'll let you know how the new one goes on.:)

I am looking for a 1952 Missouri License Plate

Ok guys I have 16" spoke wheels on my 1929 pickup.(Came that way). The hole that the cap goes into is 5 3/4". I am trying to buy caps for it, but macs says the size is from outside lip to outside lip. So what is the size I need to order? The one cap I have is 6 3/4".

Considering all things such as price, shipping and support, Which online parts store do you consider the best? "the only bad question is the one which goes unasked"

Hi guys just acquired a 1929 model A.:) I need to remove the differential so I can replace the axel bearings, however I do not have access to a spring spreader. Any suggestions?