Search results

Hello everybody, My wife and I are planning a vacation to Philadelphia this Oct and would like to take in the Hershey swap meet. What town between Hershey and Philly should we stay at that would be safe. Thank you, Jim m 29 speedster

hellow fellow barners, i had an experience with cold weather approx 42 degrees with my 29 speedster. I had it covered as we had a cold spell in southen Calif. my 6 volt battery was dead after 2 days. I charged it up and it was fine. I have seen these battery warmer that are pluged in keeping the...

Hi ford barners, Just a question relating to higher speed touring at 55 mph. For my application which in your opinion would work better. My speedster is modified with 2 stromberg 81; lake style headers and a model B distributor. Thank you, Jim m

Happy new year to all. Are there assembly instructions on the roadster windwings. Thank you Jim m Seal beach,CA

Hi everyone My 29 Speedster is 90% finished. Here are some pics you might like. Jim m Seal beach CA

Happy 4th to all barners, I have a question about the downdraft carbs using the carb risers 4”;6” and 8”. What significant benefit does this have installing a 2-carb set up on a model a engine. Thank you, Jim m

Hello everybody: question about Flathead Ted’s delux version brake floater system. On the front brakes should the top Long spring be installed? Thanks, Your help is appreciated. Jim m

Hello everyone, Just a short question: Does anyone have any information about Do-Ray fog lights. I purchased 2 for my 29 ford speedster. I would like to rebuild them. Any info would be appreciated. Jim m

Hello everyone, Just recently finished my 29 speedster. I have noticed a continuous popping noise then the engine dies. I have a model B distributor and a tilitson carb. Having trouble finding the problem could use some help. Thanks, Jim M

Hello everybody, I have some questions about the correct way to install the 29 roadster left and right cowl post. I have studied the post and the bracket that holds the cowl post to the sub rail, when the firewall slides into the sub rail does the bottom bracket fit on the bottom where the sub...

I have a question about how the 30-31 brake lite switch works. If I mount it in the correct location at the rear of the main crossmember, the brake operating rod is approx 1 inch forward in front of the switch rod. If I turn the switch around the other way which will pull instead of push, will...

A question for the forum: I'm currently building a 29 speedster I have experienced an odd occurrence. I mounted the stoplight switch on the shifting tower I hook up the attaching hook connecting the switch and brake peddle. I press down on the peddle and connecting rod protruding from the brake...

To all Fordbarn V8 collectors, I could use your help on this I'm looking for 2 hoods to complete the rear section of my 29-29 ford Speedster:) I would apprecitate your help,:cool: Jim M. 562) 537-7767

A question for the forum: I'm sure it's been discussed before I wanted to get the straight info/ can 6 volt sealed beam headlights be used with the 6 volt generator or must an alternator be used. Thank you as always, Jim M.

HAPPY New year to the Forum, My question: What is the difference if any between the AR 1928 roadster front seat and the standard 1928-1929 Roadster front seat? Thank You, your comments are appreciated Jim M.:)

I could use some help on this issue, I didn't notice until later when I connected the torque tube to the U-Joint lined up the spline. I later connected the half pieces where the transmission and torque tube meet. I noticed that the torque tube is resting on top of the brake connection shaft...

I have a question about the dust caps located on the inside of the brakes. I'm puzzled on how to correctly attach them. Is there a simple method, or must they be pressed on by a C-Clamp before the emergency brakes are attached. Any help on this issue is appreciated, Jim M.:)

I am about to attempt to replace the side cowl panels on my 29 firewall/rust at the bottom. Is there a correct or easier procedure for the replacement. Your help is appreciated. Coating03

Has anyone had any experience using the BB1 S carb on the model A engine. There are different sizes depending on engine sizes 4;6 or 8 cylinder. I understand they were very successful carburators for GM in the 30's and 40's. Carter BB1; Carter BB2 and Carter BB3 each one has a larger throat...

I have made an attempt to install the model a engine in my newly built A chassi. I'm having a rough time lowering it into the rear original motor mounts having installed new mount pads. What is the correct sequence in installing the engine, should the front yoke motor mount be installed and...