Search results

Selling a brand new 1930-31 ford coupe wood header. Bought brand new at Brattons for $135. Selling for $90 cant load pics on here. Email or text me for pics Kontinu1@comcast.net 6092009916 Thanks Josh

Looking for an Evans model A or B 4cylinder banger dual carb intake manifold. Thanks

I recently got a winfield head 6.8:1. There is no relief cut for the piston and my piston comes up about .055 above the block. The gasket i have is only .60 and thats not compressed yet so much know this isnt going to work. I used a copper felpro 7013 previously and after i took that off its...

Hi, I got a problem with the new high compression 5.5 to 1 head. I recently had my engine fully rebuilt. When I got the engine back put coolant in it and warmed up the engine. Within a few minutes I had coolant coming out of the side of the head, long story short I pulled it back off and it must...

Just got my engine back from a full rebuild. I got it installed and am putting all the stuff back on. It's almost time to put some fresh oil in it and start it up. I think before I had it rebuilt I used 20-50. What do you recommend is good for it now. I know there will be a bunch if different...

I tore down a 52 ford pickup flathead v8. I have a good crank, bearings, cam, main caps, etc. $100, I also have all other parts off of the engine, ask if your looking for something. I am keeping the carb.

This is a 3 speed side shift open drive transmission. has throw out bearing and yoke with it. shifts fine. I tore down a 52 engine block and have other parts, ask if you need anything off of it

I have done a lot of work to my 31 coupe. I have oil coming out of the rear Babbitt bearing. (As far as I can tell). I replaced the paper gasket between engine block and flywheel housing. I took off the Babbitt bottom cap and removed shims. It's seemed to greatly reduce the amount of oil coming...

I'm in the process of putting in the new Modern style valve guides and valves. The old guides were 2 piece and the new ones are a one piece style. I'd there a trick to getting them seated into the block? I don't want to pound on them and cause damage. I tried some heat on the guides but still...

I'm working on a really bad oil leak from the rear of the engine. So far I've pulled the pan and put new gaskets on. I've pulled the rear Babbitt and checked that all out. I put all back together and ran engine for ten minutes or so. I then noticed oil coming from the back of the engine still...

I have an exhaust leak at the clamp of the manifold and exhaust tubing. I have the two lined up perfectly and tight. For some reason I just can't get it to stop leaking. I also tried the little asbestos gasket you can put in between. I took off the tailpipe n muffler and made sure the lip is not...

For sale is 5 rims with tires n tubes. 1931 19inch rims Brand new tires and tubes on 4 of them less than 50 miles 1old tire n tube. Good for spare. $500 for all. Also have adapter rims to put on 30's 40's drum brakes. Kontinu1@comcast.net 6092009916 Josh

I have an FS ignition distributor and was wondering if I have to put oil in it to keep it lubed up. I think I put a little bearing grease on it when I Installed it. Its been maybe 75 miles since, I dont wanna ruin it just wondering if anyone that has this newer distributor set up andwhat do you...

For sale is a 1931 intake manifold, rebuilt zenith carb, and new air cleaner. $125 for everything, carb works and runs. buyer pays shipping Thanks josh 609-200-9916 kontinu1@comcast.net

For sale is a working 1931 generator, I had the car running then disconnected the battery and it still ran untill I turned the car off. Only took it off because I went to 12 volt system. $50 and buyer pays shipping. thanks, josh 609-200-9916 kontinu1@comcast.net