Search results

Can someone share any info on the little green sports coupe on page 15 of the current Model A news. (Nov-Dec 2015) I think it looks neat. Is part of the body VW?

Are there any 30-31 floor mats available at the present time with only pedel and column holes? I need one without gearshift and parking brake holes. Any information appreciated. Thanks

Can someone post a wireing diagram or tell me how to wire a snyder's horn relay part number a-13820 ? I have one and don't want to blow it. It has a yellow wire,a blue wire and a red wire. Thanks

Did Model A's come from the factory with gear shift and parking brake floorboard boots? Thanks

Can someone tell me what nails Henry used to hold the alumnium door sills in the A-400 and the Victoria. Are they stainless, what length and what head? Flat or rounded. Where can they be bought? Thanks, Jim

I want to add a passenger side tail light to a 31 sedan. I have a new bracket that isn't even close to matching the orignal one on the drivers side. It is shorter,thiner metal and a diffrent angle. It is stamped R. I assume that is for the right side. I am hopeing someone sells a more orignal...

Can someone tell me the compression ratio for a unmilled speed head? It has the numbers A6050B cast on it. I assume it was made 11-28-35 That is also cast on it. Also anyone out there now useing this type head? Please say something good about it. Thanks

Can someone tell what the casting numbers are on a f1 ford steering box is, I know the f100 casting number is 3cc003 I have a 3cc031 and don't know what it is for (or fits)

Can someone tell me the thickness of the spacer used on the front spindles when installing 39 to 48 backing plates and drums on a model A ? This is the spacer that moves the inter bearing out on the spindel. They are sold by Cling's, MT and others. They look to me like inserted valve seats...

Did ford in 1940 put a column shift (side shift) trans with their 60 hp v8. If so was it a smaller trans like the 37,38 and 39 top loader was ? or did they only have the small top loader for all four years? I am speeking of passenger cars, not trucks. Hope my question isn't too confusing.

Somewhere on the search page I found a sketch or picture showing the brake cross shaft being used to activate a master cylinder under the passanger seat or floor board. Can someone help me find it again? Thanks in advance. Jim

What is the HAMM board? Is that a Ford disusion site? I have had no luck finding it. Google didn't wotk for me. Thanks

I am considering putting a f100 steering gear conversion in my 31 coupe. Will you barners that have done this please share an opinon? And make suggestions as to where to purchase one.

I am sure this question has been asked before. But here it goes again. What woud be a reasonable rpm rate to cruise a 1940 v8 60 hp engine at? The engine it a new rebuild with about 400 break in miles on it. Runs great! I am hopeing someone that has one can answer this from experience for me. It...

OK mathematicians, Can anyone tell me how many rpms a engine would be turning if you have a manual three speed transmission (no over drive)and you have a 4.44 differential and tires that are twenty eight inches in diameter and you are traveling forty miles per hour. Once again whats my rpms...

Does anyone know of a supplier of rubber floor mats without the holes cut out? It would be helpful when the late model transmission tower is in a different location. I need one for a 31 coupe.

I just today (sat) recieved two electrical parts from Snyder's. Just in time for a weekend project. Item #1 a voltage reducer for 12 to 6 volt for the sparton horn. It has 2 wires It also came with a wireing diagram. I think I could have hooked it up without a diagram ( pretty ) simple. Then I...

Can you use the 600 wt. oil in a 1939 topload transmission? I am just wondering if it would cause any problems. I just want to stop some of the leaking at the back of the transmission. It is leaking around the lower of the two shafts that go in from the back end. I just don't want to tear it...

What number bulb should I use when converting a sportlite spot light from 6 volts to 12 volts?

I am putting a new top on a 31 coupe. I have some thin foam material that came from the gaslight parts store. I can't decide to use it or the cotton underlayment that the other dealers sell. I have also been told that a thin blanket like the cheap ones sold at walmart will work good. How about...