Search results

Hi all! I have a question. Do you know how much can this rear axle Ford 1946 cost? Thank you so much for your answer. Hary.

Hi all! I need a procedure of how to adjust valves of my engine Ford V8 1946. I attach an example of another Ford V8 that I found over there. Please read this article I post and tell me how to do this in my Flathead. Thank you Hary

Dear Friends! I have this carburetor installed in a Ford V8 350, but someone told me that this is not the original one. Can you help to identify this carburetor? Thanks Hary

Feliz Año Nuevo!!!! Queridos Amigos! Estoy muy agradecido por toda la ayuda que me brindaron a lo largo de estos años, he podido gracias a todo lo leído aquí hacer que mi Ford Coupe 1946 funcione de maravilla. Pido disculpas si no pude aportar mucho sobre autos Antiguos, pero yo no coincido...

Hi all! I have doubt, my engine is hard to start at the beginning but when engine start no problem, good idle and when stop and start again no problem (engine warm). engine at idle (at the garage) for 20 minutes and not stop. I discard carburetor. This happen when start engine for first time in...

Trottle shaft movement…Help! Hi All! I post a video showing how a trottle shaft moves. I have idle problem and my engine is not a 500 RPM as must be. I smell fuel not burned. How to fix it? Can this shaft be modified to avoid any movement? Any suggestion will be very well accepted. Thank you...

Non-return valve…HELP! Dear Friends! I decided to install a non-return valve to my flathead. But, i have a doubt if the valve it is in the correct place connected. I attach a pic where I installed. What do you think? Is this correct or the non-return valve must be installed after electric...

Hello everyone! I realized that there is some oil in the distributor. And I saw that the oil travels right through the vacuum hose. I noticed that the car has trouble starting and tends to stop at low rpm. I took the carburetor out, remove it from the car, clean it, change together but just...

Hi all! The spring was broken as you can see the pic. I bought a new one but it is different. My question is If I can install it. The old one have broken pieces. I watch this bendix on Mac and it seem to be equal. In new behind the piece that has teeth has a little bolt, must I take it out...

Hi all! I finally found a material spacer to my carb. Do anybody know where to get the accurate drawing of the cab base? I know that I can do it manually but I want to know if I can do it precisely. Thanks for your helps Hary

Hi all! I need repair these trunk lift arm. I can not get the original spring for each arm. Due to new restriction un my country I can not buy spare parts in USA or another countries. Have any one of you install another system? such pneumatic arms? I saw can be install in hood lift arm I...

Hi all! I have a doubt. Can an electronic gauge being installed in my Ford 1946 12volt??? It is called Dragon gauge. It is from China. It is digital and the electrician told me that the ignition coil interference with the gauge when engine start. Is this true? Do you have any experience with...

Hi All! I have this oil leak, what must I do in this case? Who can give any advise about this? I appreciate your help. Hary

Hi all! I read over there that I need 85w-140 oil to my transmission flathead 1946, am I right? I do know how much oil put, who knows? Thanks Hary

Hi all! I notice that my steering gear is more and more heavy to drive. I wonder If someone of you have upgrade it to a more easy to drive one. I know that my steering gear is the original from factory. Nowadays it is difficult for me to park in tight places. maybe I am getting old and there...

Vacuum test and Dwell...46´59AB Hi! Today I tested the vacuum and dwell with a timing light that I bought. I attached a video about the test. I see that my engine is (setting the timing light) 8 cylinder and it is at 34º with 600 RPM. Is this correct...

Hi all! I have a doubt, in my Carb 91-99 power valve has failed, so I installed another alternative carb Holley as spare part. I noticed that in my 91-99 both idle adjusting screws work fine with one turn. And installing Holley carb need more than one turn in idle adjusting screw need as three...

Hi All Who of you have the original windshield wiper in a Ford 1946 installed? Do you have a pic to see how It look like? Any series number? I saw that someone installed a vacuum tank to help motor wiper. Is this a good idea? Thank for reading Harylufa

Dear Friends!!! I ´d like if someone can explain me, which is the difference between both distributors? My engine is a Ford 1946 59AB, Which is the correct one? Thank for your helps. Hary.

Hi All FordBarns! I ´d like to share my experience with my new water pumps I got from Skip. Water pumps arrived to my Country Argentina with out any inconvenient. I have changed them last week and I can assure that are incredible. No leaks no problem at all. My engine is running at 72 or 78...