Search results

Hi Barners, I remember that some time back there was a discussion on this very topic but I am unable to find it. Can someone point me in the right direction to find it or just tell who's front windshield seal fit and work the best? TIA and my wishes for everyone on this Forum to have a Happy...

Hi Barners, I remember these two questions being discussed here some time ago but cannot remember the answer. I have tried to search here but with no luck. #1. There are 2 bolt holes on the right and left sides in the bottom front frame cross member. A passenger car is bolted thru either the...

Hi, I hope everyone is safe during this crisis. I am looking to buy glass for my 1936 Ford Club Cabriolet. Has anyone used Vintage Glass for their antique? They are nearby. Please comment on your experience; good or bad. Thanks, Bruce/CT

Hi, I am looking for the plug with a stud attached that screws into the rear left of the 1936 Ford Engine. It goes into the boss that Oil Pressure Sender screws into, but lower. A picture is shown on page 112 of the 35-36 Book. Please e-mail me @ VINOKURS@AOL.COM Thanks, Bruce

Hi, I've gotten my instruments apart and cleaned with new glass BUT I'm having an awful time putting them back together. All goes well, at least I think, until it's time to bend over the little tabs on the back to hold the whole unit together. Haven't broken any but the unit continues to come...

Hi Barners, I am getting ready to have my rims powder coated. Does anyone have experience with a powder coating business in Connecticut? I'm looking for good or bad. I'Pricing for prep, priming and then coating? Thanks for your help. Bruce/CT

Hi, I know to most of you will seem very elementary but I am stumped. I must have developed CRS disease. How do the Front and Rear guides attach to the wishbone? Please include either photos or a diagram as I seem not to be able to visualize this. Thank you sincerely, Bruce/CT

Hi, I'm looking for a pair of original front door checks for my 1936 Ford. Some rust is OK but original steel must be restorable. NO REPO's wanted. Bruce at 203-910-7387 or VINOKURS@AOL.COM

Hi Barners, The 1936 Club Cabriolet Trunk lid has 8 hollow circles on the inside lid. Does anyone have a successful method of filling these in before paint? Thanks, Bruce

Hi, I am restoring a late 1936 Deluxe car. The light switch is very scuffed. The steering column is Russet Brown. Is the switch Brown or Black? If it's black any suggestions appreciated for making the black presentable again. Thanks and Happy, Healthy Holidays to all. Bruce/CT

Hi Barners, HELP! I am stumped and humbly asking for advise. I am putting my 1936 Club Cabriolet back together and I have run into a roadblock. The Drivers side sub-rail and floor pan were replaced after I boxed in the cabin BUT now I have a door alignment problem. The Drivers door horizontal...

Hi Barners, The rear window surround on the rear convertible top of my 1936 Club Cabriolet is a two piece unit. The exterior section should be chrome plated and the interior portion painted Sand color to match the top irons. Both of mine are chromed and I need to paint the interior piece. I am...

Hi Barners, I am searching for the elusive small metal clips that hold the stainless ring to the metal tire cover. Bob Drake does not have them. Don Rogers recommended Auveco 2192 but that item is discontinued. Any suggestions? Thanks, Bruce/CT

Hi, Do any of you use an Engine/Transmission test stand with your flat head? If yes, where did you buy it or get plans to build it? I'm considering getting or building one. About how much did it cost? Thanks, Bruce/CT

Hi Barners, I have an engine test stand that was designed to hold a Short Block Chevy engine (pardon me). I need to rework all the mounts. What angle does the engine sit when fully mounted? I logically think that it should be level with the ground but just want to hear your opinions. I know the...

Hi, I'm sure that this has been debated here before but I cannot find the thread. I have removed all the old paint off my '36 and have done some lead filling. I want to move on to the next phase of finishing. Which do I do first: primer or lay a thin sheet of Bondo? Thanks for your reply. I...

Hi Barners, The wood is all done. Now, is the seat frames for my 1936 Ford Club Cabriolet PAINTED with reduced Black oil based paint or STAINED with reduced Black stain? How much ( percent) is it reduced? Thanks, Bruce/CT

Hi, Does anyone have photo of that Funky Chicken truck that was on the Chocolate Field at Hershey this year? Please put on this site or send it to me at VINOKURS@AOM.COM Thanks, Bruce/CT

My Drivers side Rocker panel needs replacement. Contact me if you have on for sale. Thanks, Bruce VINOKURS@AOL.COM

Hi Barners, What have you used to keep your INTAKE MANIFOLDS looking good? DO NOT use comments would also be appreciated. Thanks, Bruce/CT