Search results

I have a 37 that starts right up when its cold. after i've run it for awhile , I will turn it off, and 20 min or so later it will not start. If I pump the accelerator pedal 5-6 i t may start reluctently. carb recent rebuild by Charlie NY. I put a new fuel pump on with similar results. doesn't...

I'm almost ready to remove the transmission from my 37 club cab. does it go down and out or up and out? it looks tight either way. And i would like not to remove the rear mount if that's at all possible. any thoughts are appreciated. Thanks, Ernie

Happy Easter. I have a 1934 BB truck with dual wheels. I wonder what the correct torque is. Ive seen anywhere from 50 to 100lbs. Thanks

Hello all. I’ve asked several questions about redoing the brakes on my 34 bb truck. I’ve had good info from the barn. It’s going back together and I’d like to know how how much pressure to seat the inner bearing and then how far to back it off and how much pressure to seat the outer bearing...

I have a simple question . Did Ford make a 2 ton BB truck in 1934?

I got great advice on how to remove the rear brake drum on my 34BB. I’ve discovered a broken snap ring. Does anyone know where I might locate parts? It’s a full floating axle and the snap ring is 3.24 inches in diameter. Also does anyone the purpose of it? Thanks

I'm in the process of inspecting the rear brakes on my 1934 BB truck. I have a Ford service book with minimal info. Is there someplace where I might find more detailed info? I've got the axle out and could use a little guidance. Thanks

I recently removed the rusted muffler from my 1937 club cab. I'm not sure if the muffler is correct for the car. Does anyone have the specs. of the original muffler? I'm mainly interested in overall length and the orientation of the ports. Thanks, Ernie

The last piece of my 1937 club cabriolet restoration is the top boot. Might anyone have some pictures of a completed boot in place? Thanks. Ernie

I'm in need of a coil [or two] for my 1934 dump truck. My luck with a rebuilder in Florida was not so good. I prefer to keep the original style if possible. Any comments welcome. Thanks , Ernie

I just discovered the driver's side window in my 39 coupe is cracked. Do I need to use glass setting tape when I replace it? Thickness? Any other comments on the replacement procedure are welcome. Thanks, Ernie

I have a 24 stud engine with a 37-41 style distributor/coil. Raised letters on the bell housing are D11733 and stamped after that is X7. Bore is 3.23 inches and pistons are .040 over. Its mated to a column shift transmission. the serial number on the transmission is tough to read, and I don't...

I have cleaned and rebuilt a model 94 carb [several times] using Charlie's video from Vintage Speed. new parts, gaskets, float adjustment etc. It starts and runs great, About 30-40 seconds after i shut it off, gas will leak out of the throttle body until the gas in the bowl is gone. It appears...

The headlights on my 39 coupe are working well, thanks to the advice of V8coopman. we had power to the high beam switch but no lights. My friend, a Chevy guy, aggressively worked the foot switch and all works well. Thanks, I will replace the switch soon.

I am trying to get my 39 deluxe coupe roadworthy after 13 plus years. I have no power to the headlight buckets from the lighting harness, for high and low beam. parking lights work front and rear. all the wires under the wiring harness cover on the fire wall are intact. I've cleaned the switch...

I'm removing the radiator from 39 deluxe. Do I need to remove the inner fender braces and the horns to get it out? Thanks in advance

In my 2 door, 4seat car, is there a rubber piece[s] that would be mounted on the seat bottom , and would catch the front seat backrest as it goes into the upright [driving] position? there are two triangular plates near the doors and another metal piece in the middle that supports both seats...

Did the 32 panel truck come with a V8?

I' m looking transport my 37 club cab to New Hampshire from central NY, to get a top and finally finish my project. Does anyone have any suggestions? Thanks in advance.

I bought a rear convertible frame at Hershey, supposedly for a late 30's car. The screws that hold the metal halves together appear to be an odd size. They measure approximately .118 inches. that seems to me to be a #5 screw. Can anyone verify that as I have to clean up the threads to assemble...