Search results

I have a 1940 221 block bored .080 over. New pistons would cost way more than 239 standards. can I just bore the block to 3-3/16? will wrist pins fit the 29 A rod. Thanks

Looking for a 50 F2 V8 fan shroud. Also an air cleaner clamp

Looking to buy T98 ****** for my 50 F2. Dont need a PTO. I live in NE Ohio. Thanks

Looking for a T98 ****** for my 50 F2. I want to swap out my crash box T9. Anyone close to NE Ohio. Thanks

I am going to rebuild my 50 express bed on my truck.my problem is that a previous owner removed the wood and welded a plate floor in. In doing so they modified the tail gate end of the floor. There is no longer a raised section where the boards stop. Photos and dimensions of that area would be...

Looking for the rubber edge seal for the Wood in the bed. Is it flat? How thk is it? Who sells it. I have the express bed. Thanks

I have had a 50 F2 pickup since 1963 (third owner) that has 17" widow maker rims. I want to replace the rim with a one piece rim and reuse the original center plate. This would allow me to keep the original cap and look. what 17 x 7 rim will let me do this. I have a 14" rear drum so 16" won"t...

The needle on my 40 deluxe speedometer is laying horizontal and not up on the 0 mark. Is there a needle stop? if so where is it so I can get the needle in correct spot. I haven't removed the needle from where it was originally. It works fine except for the needle. Thanks

WTB any parts for the spare tire carrier for 50 F2. Thanks

I have a 50 F2 Truck. I saw a pair of front fender splash shields on Ebay which made me check my truck. I have owned it from 1963 and I don't have any on mine. Did they have them originally? they fit in the front fender behind the wheel. Thanks

Is there someone making bed parts for an express bed for a 50 F2. This bed is 54" wide and 96.05", rounded stake pockets and embossed bed sides. Also need a spare carrier.

My 40 coupe is missing the frame section for the rear motor mount, will a section from a different year fit? I think I know where there is a 48 sedan frame that has the frame piece i can get. i attached a picture of the frame section I am looking for. thanks

When I flip the lever to start on my Ignition switch on my 40 the switch enclosure gets hot. Almost to hot to touch. Is this normal? I took it apart and it looked OK. Is there a fix? Is there a short? Thanks

I need some advice on the seat covers for my 40 deluxe. The front seat only has two sets of ribs sewn in but the Ford book says there should be three. I assume the third set is in the bottom seat only because of the sedan back is split. My back seat has no ribs at all. I don't know if these are...

Which side? My 40 deluxe had one hand grab and I believe it was on the drivers side. If it were installed on the passenger side it would cover the light switch for the courtesy lamps. Both sides have holes for it. Which side does it belong on? If I had a second one I would install it also. Let...

Would like to find a Grain-it plate to do my 40 Ford Deluxe. Could buy new but thought someone may have one they have used and no longer needed. If you have one let me know what you would take for it. Thanks

I am looking for a 1940 FORD driver side arm rest. any condition. If you have one for sale please contact me

Is the rear tray on a 40 sedan held in place or does it just lay in place. The rear seat back would hold it in I guess but I think something should hold it down. The formed tray was junk so I made one from fiberglass cloth. Does it get covered with headliner or door panel cloth? Any help would...

I just received a notice that Labaron is closed and filed chapter 7. The bad news is that they charged me for a headliner and door panels they said were ready to ship. That was 3 weeks ago. The good news is I might be able get the money back from my card company. I hope someone will buy it and...

Where can I get some round wire staples for fender welt