Search results

1930 Model A pickup. strong engine 7-1 head, good cam, insert bearings, down draft carb with a holly 94. It also has a F150 4 speed OD transmission. hydraulic brakes.

strong engine. 7-1 head, good cam, over size intake valves, inserts, down draft intake with a 94 carb, hydraulic brakes. Over all good condition.

Wanted radiator shell, front fenders, hood for 1924 T coupe.

I have been helping a couple friends built a hill climb engine. It had 8 stuck studs. They came up with a neat idea how to get them out, with out breaking them. They are Steven Grace and Bill DeVore. They took some 1/2 plastic conduit cut it about 3/4 inch long. Then put it around the stud and...

wanted 2 or 3 19" model A wheels. Would like them near NC

Is any one else getting unwanted E mail from Mack's auto. I have ask them many times to stop sending me E mail but they won't stop. Just about every day.

In April, 6 of us took my hill climb car to Unicoi TN hill climb. We made many runs and had the rev limiter set at 4500 rpms. The flywheel came loose, it broke the heads off 3 of the flywheel bolts. It damaged the flange face and flywheel so they were no longer flat and true. To fix the crank...

Wanted AA bell housing,

It is always better to preform some simple test before you change a lot of parts. First check for big blue spark. Then pull the plug out of the bottom of your carb and see if you are getting good gas flow.If you have bad gas flow it will start bucking before it stops. Try pulling the choke out...

1939 Flat head V8. Comes with original intake and a 2 carb manifold, . Has a mild cam, headers, also have the stock exhaust manifolds. It runs real good, has very good oil pressure, but has a oil leak at the rear main. Still in my 1930 pickup if you want to hear it run. The reason I want to sell...

239 flat head. Runs real good, has very good oil pressure, but has a rear main leak. Dual manifold and carbs go with it.It has headers and mild cam. but I have the original exhaust that go with it. It is still in my 1930 pickup truck, so you can hear it run. Reason for selling is I want to put...

Two multi dish flywheels, one multi disk transmission with clutch pack. Must pickup here.

Marshall did you ever find the problem with engine or trans locking up?

this car was restored from a nice original car that had been inside from 1960. I first seen this car in 1960 it belonged to a friend. I got it from his wife after his death in 2000. It has the original engine, and right number for the car. Have the title from 1938. No rust. 919-934-1858 or send...

Does any one know who much longer the 4 speed truck flywheel housing is ,than the car. I was thinking 2 1/4 inches, but not sure thanks George

You just might want to check your rear axle nuts. I have 23,000 miles on my 28 sport coupe since it was redone. At the time I torqued the axle nuts at 110 ft lbs. noticed lately that there was grease on the hub cap, so finally to day I check the one with grease on the cap. It was loose, probley...

Why is it that people do not want to try and find out where engine noise comes from before they take every thing apart?

I see a lot of Model A's with late timing. You can tell by the sound and my hearing is going. A lot of people do not get the play in the dist. right. Of coarse the carb gets the blame. I'm starting to think a lot of guys would be better of marking the pulley and using a timing light. If your...

Along the lines of keeping valves in order, the same goes for rod caps and main caps. Rod caps have to go back on the same rods and the same way they came off. Mains same thing you do not want to mix them up. I like to mark them before I take them apart. One time in my Dads garage a long time...

I see on here all the time people changing parts to fix a engine. That is like going to the Doctor and he gives you differnt kind of pills tell he finds the one that fixes the problem or kills you. Every engine has a symptom for each problem. If you change a lot of parts, you might fix it or...