Search results

I'm looking for a set of headlight reflectors for a 36 pickup. trying to go back original 6 volt stuff. Thanks

Good afternoon, I have a 36 pickup and I'm looking for a place to get the little button clips that holds the upholstery to the cab framework. I've got a few, but not enough to fasten everything properly. Thanks Mark

Good evening!! I was wanting to know the size of bolts or screws that hold down the little inspection hole plate. I'm trying to be original. Thanks everyone !

I'm trying to go back as original as possible. How much of the pickup bed was together before it was painted? I still have to put the wood down and then the metal pan on top of that. Was wondering how Henry did it. Thanks Mark

Good afternoon, I have a question about the rear fender bolts on a 36 pickup. The original ones resemble a 5/16 carriage bolt, except that the head is the size of an 1/2 inch diameter carriage bolt. And there isn't the little square area below the head. Also, how are they held in? Without...

Good morning I was hoping to learn a little bit about installing rivets. The best way, tricks, etc. Getting the tools I might need and so forth. Thanks Mark P.S. I'm putting the pickup bed back together on a 36.

I'm looking for a pair of the "Y" shaped hold down bolts. I have the top hold down frame, just need the bolts. Thanks Mark

I was trying to install a wiper motor that I have into my 36 pickup and was not having any luck aligning the control arm with the holes in the cover plate. After some time of wondering what I'm doing wrong I finally realized that my on/off arm is on the opposite side of all the pictures I was...

I have a 36 pickup. I found an original wiper motor to put back in this thing. I'm not sure how it mounts. The spot where it goes has no brackets, the wiper motor doesn't have any mounting holes. So far the only thing that I have to hold it in place is the rubber grommet to the outside world...

I'm looking for a pair of 36 pickup (half ton) inner fender wells. I understand that 1 1/2 ton truck one are pretty close. Just have to do a little trimming along the bottom. I can work with just about any condition too. They have to be better than what I have. Thanks Mark

Good morning. I was wondering where a guy can get the drawings for the front inner fender wells on a 36 pickup? Mine are butchered up some and I'd like to see what they are suppose to look like. Thanks Mark

I am in need of the horn and light switch assembly. Needing the rod and the horn button and light switch. Thanks

When I took my running boards off the right side was held with 2 carriage bolts on the front bracket and 3 on the back bracket. Same on the left side except for the extra one that also held the fuel line. Now I'm putting them back on after the restoration. My question is that there are more...

Hello, I'm needing to get a temp. guage for my 36. Is there anyone that makes after market ones or someone that can repair an old one? Thanks Mark

I have a 36 pickup, and I was needing a picture of the floorboard that bolts in to the firewall and the wood floorboard. the one that the peddles go thru. The one I have has been cut on to make room for something else. I need to do some patching on mine to get it back to original. Thanks Mark

I have a 1936 radiator that really needs some work. Besides needing cleaned up, it needs new water inlets and outlets attached. Someone removed one of each when they had a different engine installed that didn't use 2 ins and 2 outs. I live in the Springfield , MO area so someplace in the...

I have a 36 pickup. I was needing to know what is used in the little hole in the strap to the bracket on the cab? A little bolt was in there when I took things apart. It wasn't factory because each door didn't have the same bolt in it. Thanks Mark

Hello! I'm taking apart a hand brake handle and trying to make it like it came from the factory. I was wondering if it was painted before assembly or after? Thanks Mark

I'm am looking for a 1936 hand brake, parking brake assembly. Thank you

Good afternoon! I'm getting ready to mount the cab of the pickup back onto the chassis. Is there anything that goes between the wood and the cab or anything between the wood and the frame? When I took all this apart, it was hard to tell what was there. Thanks in advance!!! Mark