Search results

Cobramik has answered an add I have. Scammer or not? Thanks

I have a complete Tyree Harris harness that has been used less than a year the harness includes all "bullet connectors" male and matching female as original. Also included is a column mounted turn signal switch that matches and is tied into the main harness. wiring for the turn signal switch...

1940-41 pickup seat complete minus upholstry I'm selling new bottom and base springs with wood base attached to the back spring as original. I'll now add the seat riser to the bundle. I'll also add a picture. price drop $300, offer

I have a 10 in. long rod from carb. to the pedal assembly, but the accelerator pedal hits the floor before the butterflies are fully open. It looks like I either reshape the spoon pedal or shorten the rod to the carb. I did a search and it seems that rod was shortened from the earlier length of...

New member. He answered my wanted add for '40 STD hubcaps.

I'm looking for the correct hubcaps for my '41 p/u. I have 3 repos and I need one more repo that matches. They are the same as 1940 Standard car caps.

I am in the process of fitting patch panels and since the the "A" pillars were rusted off just below the bottom hinge, the lowest fender mount hole is gone and I'm trying to use the upper 2 fender mount holes and the running board to find the missing hole location. If someone could post a...

I need the center body ( jets and accelerator pump located ) for a pre 8ba 94 in good condition. Model 91-29, 91-99, or 59. One of the jet well plugs is stripped and not correctly repaired. This is for the 59A in my 41 pickup. Thanks. Joel P.S. no 8ba carbs ,please.

I just fired the 59A for the first time and it went pretty well except the crank mounted fan skinned the lower radiator hoses. This fan was on the engine in a '40 2dr sedan I bought so I assumed it was correct. Is this the correct fan for my truck?

I have pair of 54-56 F100 backing plates and drums and one hub. I think it is a 37-40 hub and the register diameter on the hub is 3.253; while the hole in the drum is about .100 in. smaller. Question; did that dia. change over time do I cut the register on the hubs to match( lathe)? Thanks .Joel

i want both parts of the 2 piece oil pan for a 59 AB engine . I believe it was a truck only. It allowed the clutch and flywheel to be changed with out removing the oil pan.

I have Best copper sandwich head gaskets . They are identical. each has some smaller water holes in one end of the gasket. The other end has holes the same size as the head. (edelbrock heads) my question is ; do the small holes in the gaslet go to the waterpunp end or to the bell housing end...

I am using the 8ba helical gear oil pump with the 50 psi relief spring and the original block relief plunger has a flat on it that appears to allow "leakage" into the cam gear compartment. I also have a new plunger and spring and this plunger does not have the flat on it . Which should I use? I...

The bore is fresh and about .003-.004 oversize. This is an old build that was assembled and never fired. I am trying to reassemble it with the parts it came with. The end gap on the new rings is .020 and it should be .014. I haven't been able to find oversize rings to file to the correct gap...

I'm trying to find out if the " channel " in the lower left in the picture is supposed to be there. This is how I found it. The picture on the right shows the relative location on the back of the pan. Thanks. Joel

drivers door lower hinge 41 pickup Found My 41 light duty pickup drivers door lower hinge is practically destroyed. The part welded to the door is what I really need. I will take a complete unit. As far as I know, it should be the same up to '47. Thanks. Joel

40-48 front brake backing plates These were removed from my 41 light duty pickup. Everything works as it should. The drums appear to be slightly over 12 in. dia, but do not need to be turned. $30 ea. for the drums SOLD $120 for the backing plate assemblies

These are off my '41 pickup. P O removed the 6 cyl. front cross member and bolted these to the V8 cross member he installed. They may have 1 extra hole he used to install the new radiator. They appear to be in very good condition. Buyer pays shipping . If you need more pictures, just ask. price...

This a V8 cross member that came with my 41 pickup so I cant' verify the year. It's in very good condition. Buyer pays shipping. If you need more pictures, ask.

I'm listing for a friend who is unable to. This is the best info I have. Early 20s C cab body with later T bed. No frame; no title. The cowl is pretty nice and the sub rails are decent. I have taken a lot of pictures, but ask if you need to see more. The black paint is Hirsch Miracle paint I...