Search results

We are looking for 1933-34 rear brake drum that has good studs and at least 30 thousands of wear left. We want to get back on the road. A picture of drum would be appreciated as well as a measurement of the inside drum diameter. Thanks for looking and happy V8ing. PM or email...

We need the cover plate that goes over the gas sender unit opening for a 1934 pick up truck bed Any leads to finding one is appreciated PM or mjfehniger99@gmail .com Thanks for looking if you have one

Ford Barn guys, For a '33/'34 pickup, we are interested in how you have supported the rear of engine when replacing the transmission via removal of the rear end. How supported and where supported would be greatly appreciated. Thanks, Mike and Steve

Ford Barn guys, we have run into a issue as finishing a radiator replacement on our '35 Tudor Touring Sedan. The hood latches in 3 of 4 places. However, the right front hood latch will not engage the bracket mounted to side of radiator. We have determined the position of this bracket, although...

We have the gas sender out of of our '35. We want to clean it out before reinstalling it. We were thinking of soaking it in a solvent. Any suggestions on how we we should go about cleaning it out? Thanks Mike

We are looking for the longer luggage rack mounting brackets that are unique to Ford touring sedan models for 1935-1936. The brackets are about 3" longer than the brackets used on other Ford models. These brackets were reproduced many years ago, but are no longer available. There are probably...

We are looking for a 1935 gas sender unit that mounts in the gas tank that is either NOS or one that on that is in excellent condition. If you have one that you are willing to part with you can contact us at mjfehniger99@gmail.com or by a PM. A picture of the sender would be greatly...

We are replacing the '33 transmission in our '33 pickup with a '39 gear set in a '37 transmission housing. The shift tower we are using is a 81-A. With this transmission setup what gear shift lever should we use to avoid hitting the seat? In addition, what else do we need to consider to be...

We are looking for a source that can restore our 1933 and 1935 hydrostatic dash gauges. These are the ones that have the red fluid in the tube. We have run out of gas not knowing we were that low. Any help in finding a source that can rebuild these gauges would be appreciated. Thank you and...

Went to winterize the '35. The pet ***** would not turn, they were frozen. Started to remove one pet **** from the block but I could not remove it due to interference with the front cross member. I could not get it out. Have any of you guys had a similar problem in removing them? Any help...

Who can I send this gauge to for restoration. Thanks mike

We have a 39 gear set mounted in a 1937 case that we want to use in our stock '35 Can we just bolt this '37 transmission into the '35 or do we have to make modifications to the '35 drive train to get this combination to work? Thanks for your technical help. Happy v8ing Mike

Can you put a '39 transmission gear set into a model 48 ('35 transmission case . with a 81 gear shift housing and have it work?

We are looking for the pins that are located on both ends of the cross shaft that secure the bronze bushing to the cross shaft. The Ford part number is: 352581-S Any help in locating them would by appreciated. Thank you and happy V8ing Mike

FOUND Looking for a NOS or NOSR '33-'34 Stop light switch Thanks Mike PM or email mjfehniger99@gmail.com

On our '34, when we have the brake lights on and then when the headlights are turned on the brake light goes off. This only happens on one brake light, the other performs normally. In studying this problem, we observed that only one filament was being used by both. We changed out numerous...

Set of 8 1933-'34 brake shoe cores These shoes have a bonded lining on them. Price is $75 plus shipping in a USPS flat rate box, PM or email me at mjfehniger99@gmail.com Thanks Mike.

1933/34 Ford Pickup for sale. This driver is on a 33 chassis equipped with a 34 cab, hood, grill and a 35 tailgate. All steel sheet metal including metal front apron. Blue Rock Green with black fenders, Tacoma Cream wheels. Relatively fresh acrylic enamel paint on fenders and box, which need to...

For Sale: Rebuilt starter and bendix Price $50 plus shipping. PM or email me. mjfehniger99@gmail.com.

For Sale 51A-7113. cluster gear. Has good teeth, used no chips. 14x18x24x28 $75 plus USPS flat rate shipping PM or mjfehniger99@gmail.com