Recent content by roger248young

Looking for an original rear driver's side interior door panel for my son's '38 Ford Standard Four Door Sedan. Also, need a front seat cover and a hood handle. Please PM or call 248-585-six 780 (no texting avail.). BIG thanks Roger.

Looking for an original rear driver's side interior door panel for my son's '38 Ford Standard Four Door Sedan. Also, need a front seat cover and a hood handle. Please PM or call 248-585-six 780. BIG thanks Roger.

Looking for a nice 1938 Ford Standard Hood Handle #81A8215-A for my son's project car. It looks like a '37 handle, but it has approximately 2" longer pivot shaft. I think the '38 shaft is about 5-3/4" long from the bottom of handle base to the end of the shaft. Please PM or call 248-585-six...

Looking for a nice 1938 Ford Standard Hood Handle #81A8215-A for my son's project car. It looks like a '37 handle, but it has approximately 2" longer pivot shaft. I think the shaft is about 5-3/4" long from the bottom of handle base to the end of the shaft. Please PM or call 248-585-six 780...

Thanks guys for all the good information. Now, If a Ford Barn member needed an original 1932 hand crank with correct length extension for their vehicle, I could machine the end length to suit from a 20-1/8"long square end taper extension which does not fit my '38. Hopefully, I can help somebody...

Hey Bruce, Thanks for your quick reply. Based on your comments, I think that my hand crank that accepts round sloped flat extension was an early design for the 4-cyl. Model B. Do you think this design was used on 4-cyl engines up to 1934? Also, does the 17.8" long extension sound right? Thanks...

Hi guys, I am hoping that you could help me figure out my crank handle which I found in my 1938 Ford trunk. This crank handle accepts an extension with round flat taper on one side(not square). Do you know what year ford(s) this was used, and the length of extension for this handle? I think that...

Hi Lloyd, I'm interested in your distributor. Please E-mail some pictures to show condition of inside cam and bottom tang. Thanks, ryoung248@comcast.net

Hi, I am looking for an original interior left (driver's side) rear door panel for my 1938 Ford Standard 81A Fordor Sedan. Trying to find one that is better condition than mine(see attached photo). Also, looking for good condition original(or NOS)headlight reflector for the 38. Thanks...

Hi, Still looking for an original driver's side visor which measures 5-7/8" X 15-1/2" for my '38 Ford Standard 4-Door Sedan. It needs to be light brown/beige with dark brown edging to match my existing passenger side. Please contact Roger at "ryoung248@comcast.net". Thanks Ford Barn.

Hi, I am looking for the front and rear wheel mechanical brake shoe centering tools for setting the shoes on my '38 Ford Standard 85 HP 4-door. Please E-mail "ryoung248@comcast.net". Thanks Ford Barn.

Hi, Still looking for driver's side visor for my '38 Ford Standard 4-Door driver. It measures 5-7/8" wide X 15-1/2" long and is beige with dark brown edging. Please E-mail Roger at "ryoung248@comcast.net". Thanks Ford Barn.

Hey Bill, Any luck finding an interior visor? Still looking. Thanks, Roger

Hi Modifieddriver, Would you have a driver's side visor for my '38 Standard driver? The measurements are 5-7/8" X 15-1/2" and is beige with dark brown edging. Please E-mail: ryoung248@comcast.net Thanks, Roger

Hi Aarestor, Would you have a driver's side interior visor? I am trying to match my '38 Fordor passenger's side visor which measures 5-7/8" X 15-1/2" and is beige with dark brown edging. Please E-mail "ryoung248@comcast.net". Thanks, Roger