Hoist Question

There is no particular reason that will not work. Some members will not recommend the Harbor Freight product. For occasional use it will be fine. You will need either 1 or 2 eyelets that are sold through the national vendors or a plate to bolt on top of the motor as an aid to hoisting the motor out of the car.
 
Seth that cherry picker will work fine for you. one of the few things i own from harbor freight is that. i just use the eye hook in #3 plug hole to lift it out simple and easy
no rocket science needed
 
I have the two ton version of this shop crane and recently removed the engine from my A with no problems. I ran a short piece of chain between two eyelets screwed into the cylinder head and attached the crane hook to the chain.
 
I figure that the hoist will be used for removal and re-installation by me once. I can't see me using it much after doing this work but will add it to the local club's "available tools" list. If there are alternative hoists on the market, I would consider them as well.
 
i use mine all the time
here is the eye hook off brattons FYI or you can do it 50 other ways chain, seatbelt etc
 

Attachments

  • image.jpg
    image.jpg
    43 KB · Views: 53
I have had that very lift for over 10 years and have punished it severely yet it has yet to fail me. (I have suspended complete rolling chassis, without drivetrain, off the ground for sandblasting, with a 15 foot extension stuck in the end.... do not attempt this at home...i'm an professional idiot :eek: )

This is built well enough to stand a lot of use.

Remember to take you discount coupon with you.
 
sethkestenbaum said:
I figure that the hoist will be used for removal and re-installation by me once. I can't see me using it much after doing this work but will add it to the local club's "available tools" list. If there are alternative hoists on the market, I would consider them as well.
Click to expand...

If you are using the hoist only once, I would check into renting one. The problem with owning one is finding a place to store it when not in use. But maybe you have lots of room.
 
fiddlybits said:
I have had that very lift for over 10 years and have punished it severely yet it has yet to fail me. (I have suspended complete rolling chassis, without drivetrain, off the ground for sandblasting, with a 15 foot extension stuck in the end.... do not attempt this at home...i'm an professional idiot :eek: )

This is built well enough to stand a lot of use.

Remember to take you discount coupon with you.
Click to expand...

Hmm, I get this mental visual, that makes me smile :) ! Great idea, think I'll borrow it ! BTW...Pics would complete story.
 
I bought this same unit but in the 2 ton capacity and it is great. I also have used it for body removal off of my roadster. When it is not in use the legs fold up and it is just pushed in the corner where it takes very little room.
 
I have the same cherry picker. I pulled my engine and transmission this morning. It worked flawlessly.

Occasionally HF has a coupon for this lift for $99. Ask around, you might get lucky and find one.

Good luck with your project,

Dan
 
1 ton is more than adequate for Model A work, and a folding crane makes storage easier. I can't find a rental shop that will offer one here any more. They all claim they come back damaged because guys misuse them. I'd say buy it; you'll be surprised how often you can use it.
 
I have the same hoist and like the others had no problem installing the engine along with bell housing and transmission HOWEVER when putting it on or off the engine stand it is a little awkward although doable (sp?). The engine stand is a HB product also.
 
fiddlybits said:
I have had that very lift for over 10 years and have punished it severely yet it has yet to fail me. (I have suspended complete rolling chassis, without drivetrain, off the ground for sandblasting, with a 15 foot extension stuck in the end.... do not attempt this at home...i'm an professional idiot :eek: )

This is built well enough to stand a lot of use.

Remember to take you discount coupon with you.
Click to expand...

hardtimes said:
Hmm, I get this mental visual, that makes me smile :) ! Great idea, think I'll borrow it ! BTW...Pics would complete story.
Click to expand...

OK, here ya go... I could not quickly find the fully lifted pic but this should give you the idea. The sling was eventually attached to the end of the extension and pretty much put the chassis vertical.
 

Attachments

  • hoist.jpg
    hoist.jpg
    81.4 KB · Views: 139
I've been going thru the process of deciding whether or not to get one of these. The biggest problem is that of adequate storage when it's not in use, but I think I can live with that. I probably wouldn't mind the HF unit; price is right, but the freight would kill me. Soooooo, I've been looking at Amazon (prime=free shipping) or Craigs list locally = no freight. Having it when I need it and not having to beg/borrow is my greatest push. I've already had to do that twice, and could again if I have to.

I just like having my own tools! Isn't that what owning a Model A is all about?? An excuse to buy more tools.
 
To all... thank you for the inputs. I've decided to go with this model.

Dan... you inspired me to look for a coupon. I found a HF 20% off one that didn't work online when I tried to use it. This was a good thing. I called HF to have them figure out why. We resolved the issue and it worked. Goofing around with the woman on the phone, I asked if there were any "better coupons". She found one. I was able to get the hoist for $99. With delivery and taxes it came to $115. Dan, I owe you a beer.
 
Carl G, give HF a call. The shipping on mine was almost nothing. I don't know if that $6.99 standard shipping applies to Alaska, but you might as well ask.
 
CarlG said:
I've been going thru the process of deciding whether or not to get one of these. The biggest problem is that of adequate storage when it's not in use, but I think I can live with that.

I just like having my own tools! Isn't that what owning a Model A is all about?? An excuse to buy more tools.
Click to expand...

I didn't get the fold up one. I just take mine apart and store it in 'the rafters' of my garage. I need my floor space.

Your right, I'm the same way about having my own tools. Learned a long time ago when I was a Motorcycle Mechanic not to lend or borrow tools...

I must admit owning an "A" kind of forces you to buy some "A" specific tools but it is really is an excuse to buy more tools.
"But Honey, I can't change my Stop Light Fluid without this special wrench".:rolleyes::rolleyes:
 
You must log in or register to reply here.
Back
Top