32 - 34 gas caps

Chris Marshall

Chris Marshall

Senior Member
Does anyone make a gas cap that will actually seal and keep gasoline from leaking out of an original 32 - 34 tank? I'd rather have an unvented cap, but will try anything that will actually hold gas in the tank.

I've tried many tricks to get them to seal including cutting a second gasket and other ideas. So far I still get gas sloshing out onto the paint on both my '32 and '33.

I appreciate any ideas/help.
 
Chris Marshall said:
Does anyone make a gas cap that will actually seal and keep gasoline from leaking out of an original 32 - 34 tank? ...
I appreciate any ideas/help.
Click to expand...

The question... No I don't think one exists. On the ideas... I have fixed the issue for the most part by refusing to fill the tank over 3/4, and even then I'm careful and regretful. '35-'36's do it when just the slightest bit full and taking a curve to the right.
 
Chris, try smearing a bit of grease on the gasket you made. It works for me, (well, kinda). Good luck, Doug.
 
In my opinion in regards to repro caps the Vintique cap seals the best in original tanks. Stant makes a cap that seals well but looks nothing like a original and is vented
 
They do, I had the same problem on my 33 ,it would spew gas out on corners!finally worked it out!Had a vented cap on ,the one most suppliers sell,I fixed it by getting a non vented one from Sacramento vin ford,
Lawrie
 
I took a piece of old inner tube & attached it to the filler neck & let it drain down the tube drain/slide. Hardly notice it.
 
I use original non-vented caps with NOS leather gaskets for pre-36s and have not had spillage.
 
35ford, yes I think it was!i bought two so I had a spare in the 33: if you want a picket. Me know,I,m sure it’s not the 100% correct one as with the v8 logo it doesn’t do up straight!but I got a plane one as well,they both work well and don’t leak.
Lawrie
 
Pre-'36 they are vented at the fuel pickup on top of the tank so a vented cap is both redundant and an exit route for spillage.
 
DavidG said:
Pre-'36 they are vented at the fuel pickup on top of the tank so a vented cap is both redundant and an exit route for spillage.
Click to expand...
David, What did Ford do on trucks with the under seat tank where the fuel sender goes in from the bottom of the tank?
 
I use a vented cap on the 34 but i have a spot of weld on the inside over the vent hole, a gasket cut from a bit of plumbers roofing rubber (Bout nol ) works great ,have not worried about it for 20 years ,
 
The thread I referenced from 2012 said Vintique was started by the same family as CW Moss. I called CW Moss and they said they handled Vintique components but that they are out of stock on the Vintique gas caps and don't know when they would have them. Looks like a dead end for a Vintique gas cap unless you can find NOS.
 
Fairly sure our cap on the 32 is vintique ,not original as it has the V8 stamped in it. Tried all sorts to stop the leak from under the cap.
Went to this cap , never a drop leaks out now.
 
CW Moss said they had a V8 cap from Drake. I saw Joe's Auto was also listing a Drake V8 Cap. Do you think your cap may have come from Bob Drake?
 
As far as I know there has not been a non vented gas cap made for Ford V8's because of the mechanism. They say there was one made for the 1935 Ford V8 models with the inscription on it.
 

Attachments

  • Non Vented.jpg
    Non Vented.jpg
    52.6 KB · Views: 19
  • Vented type 2.jpg
    Vented type 2.jpg
    42.8 KB · Views: 18
You must log in or register to reply here.
Back
Top